1
DAQ Software/Firmware / Re: exposure time and frame rate
« on: July 01, 2017, 04:12:28 PM »
Thank you so much !!!!
dylan
dylan
News:
The Miniscope Forum Board uses a separate account from your Miniscope.org
Our old Discussion Board can be found at http://miniscope.org/index.php?title=Special:WikiForum
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
DAQ Software/Firmware / exposure time and frame rate
« on: July 01, 2017, 03:03:56 PM »
Hello, we did test the scope by Inscopix, which has exposure time numbers automatically adjusted by frame rate. But our miniscope show only the constant number 100 to 255 while adjusting the frame rate. In our software, it automatically calculate and assign the maximum exposure time as 255 depended on frame rate ?? Or, we need to recalculate and adjust the exposure time value by frame rate? Thank you
dylan
dylan
3
General Discussion / upcoming workshop
« on: April 17, 2017, 04:38:29 PM »
Hello, Our team members are interested in the upcoming workshop. When it will be opening? Thank you!
4
DAQ Software/Firmware / Re: mscam frame retrieval error
« on: April 14, 2017, 01:04:44 PM »
Thank you Daniel.
We tested with the laptop (i7 and Windows10) and nailed it. All failed computers were i7 and Windows7.
We tested with the laptop (i7 and Windows10) and nailed it. All failed computers were i7 and Windows7.
5
DAQ Software/Firmware / Re: mscam frame retrieval error
« on: April 12, 2017, 03:39:12 PM »
Thank you Daniel !!
Our manufacturer fabricated three LEDs with reverse orientation on DAQ board. So, we could not check the state by three LEDs. But, connection with CMOS could make it by red LED and blue LED on CMOS boards. They both turn on - voltage power transmits. We have been tried with different USB cables and CMOS boards, but it has yet failed. So we are still waiting for the order of 2016.
Our manufacturer fabricated three LEDs with reverse orientation on DAQ board. So, we could not check the state by three LEDs. But, connection with CMOS could make it by red LED and blue LED on CMOS boards. They both turn on - voltage power transmits. We have been tried with different USB cables and CMOS boards, but it has yet failed. So we are still waiting for the order of 2016.
6
DAQ Software/Firmware / mscam frame retrieval error
« on: April 08, 2017, 04:19:57 PM »
Hello, We need your help..
We personally ordered the 3.2v CMOS and DAQ PCB not by UCLA groups. Placed switches and successfully uploaded firmware with K2 K1. But then, only connected with K2 and CMOS, it failed to get frame retrieval. The red LED on CMOS and the Blue LED lit up, but we were not able to adjust the intensity. And the cognition as MINISCOPE in device manager happened 'rarely'.
We used Cooner Wire 50ohm coax and USB3.0 cable. (changed 2 different 3.0 cable, but it failed as well)
5V in J4, 2.5V in blue LED, 1.7V(not exactly) in red LED.
We personally ordered the 3.2v CMOS and DAQ PCB not by UCLA groups. Placed switches and successfully uploaded firmware with K2 K1. But then, only connected with K2 and CMOS, it failed to get frame retrieval. The red LED on CMOS and the Blue LED lit up, but we were not able to adjust the intensity. And the cognition as MINISCOPE in device manager happened 'rarely'.
We used Cooner Wire 50ohm coax and USB3.0 cable. (changed 2 different 3.0 cable, but it failed as well)
5V in J4, 2.5V in blue LED, 1.7V(not exactly) in red LED.
Pages: [1]